Yes, of course, this function is present.
Gazer’s voice-controlled remotes are sold under the name Gazer RC15. Gazer Smart TVs also support Bluetooth remote controls that have a built-in voice input function.
In order to view the contents of the external drive, you can use any file manager or media player from Google Play. Also, by default, the TV is equipped with a file manager with a built-in media player, which is called “Media Player” in the list of programs.
So, in the Gazer TV, the lower two holes are unthreaded, you need to screw the lower bolts into them, which will create a thread. In the latest deliveries, all TVs come with bolts for the lower holes.
At the moment, there are two versions of Gazer TVs: Android 7.1 and Android 9.0. Models from 2020 release run on Android 9.0. You can check the TV release year in the store before buying.
No. The image coming from such a DVR will not be mirrored. As a result, objects to the left of the car will be displayed on the right of the monitor, and vice versa. In addition, such a DVR is installed only inside the car, as it is not intended for service in conditions of road dust, weather, precipitation and washing the car with a jet of water under high pressure.
At the moment, current models of registrars work only with drives formatted in fat32 format.
Yes, our recorders can work in wifi access point mode if you have a sim card, but only one device can connect to the point at a time.
The DVR records in ring (cyclic) mode. In the DVR menu, you set the duration of the video in minutes, and the DVR sequentially records video files of the set duration. When the free space on the memory card runs out, the DVR will delete the oldest video file and replace it with the current one. And so – every time.
To do this, go to the menu, activate the item “display captions” (the name may vary depending on the model). And then, in the paragraph “state. number “, enter the appropriate number of your car. Under such settings, the state. your car number will be displayed correctly in the video.
To do this, simply remove the memory card from the DVR and connect it to your computer via the appropriate card reader, then copy the desired videos to your computer. If you do not have a card reader, you can connect the DVR to your computer with the included cable and then copy the necessary files.
If the Wi-Fi network of your registrar has “Direct-” in its name, then try resetting your registrar. To do this, turn it on, quickly press the power button nine times, wait two seconds, and briefly press it again. The device will reboot and you can connect. Also, mobile data must be turned off during connection.
To restart the recorder, you need to turn it off, unplug the power cord from the recorder, and then press and hold the Reset button for at least 5 seconds. Also, make sure you press the Reset button. When you press it, you will hear the characteristic sound of the microphone contact. If the recorder does not reach normal operation, repeat this operation. If this does not help, please contact a service center.
In some cars, there is interference with the radio with the DVR on. Interference may also be related to the operation of the power supply of the Gazer DVR, which uses a pulse voltage conversion circuit.
To avoid interference, please do not install the DVR’s power cord near the radio antenna. Do not place the main power supply of the DVR in close proximity to the radio or its antenna connector. You can easily use cigarette lighter socket extensions to remove the cigarette lighter socket and the DVR power supply from the car radio.
The recorder always records on the memory card, regardless of the presence of an Internet connection.
An important feature of Gazer DVRs is the availability of a certificate for the entire product range. This certificate is a guarantee that the use of Gazer DVRs is completely legal and safe. The presence of the certificate also confirms compliance with the stated characteristics, and therefore the high quality of the DVR.
So. All power supplies supplied with the Gazer DVR can be connected to a 24V car network.
All Gazer DVR models (except F150 / F150g and F145) have the ability to quickly deploy the recorder body around its axis to capture events inside the car. You can deploy a recorder or a separate video camera model to record your conversation with passengers in the cabin or other people through the side window of your car.
Vacuum mounts or 3M tape mounts are used to mount the Gazer car recorder to the car windshield. Vacuum type allows you to quickly install and remove the mount from the windshield of the car with minimal effort – using the locking lever on the mounting body.
Depending on the DVR model, different mechanisms are used to connect the DVR housing to the mount. Regardless of the model, you can quickly detach the DVR housing from the mount with minimal effort.
No, storage devices are not included in the package.
Gazer recorders turn on automatically when the power is turned on, and turn off automatically when the power is turned off. Probably, in your car current through the cigarette lighter socket is supplied only with the engine running. In this case, the DVR automatically stops recording. Then this is the normal mode of operation of the recorder.
Such failures may be related to power in the car. If the current in the cigarette lighter socket is supplied only when the engine is running, then at the time of starting the motor, the electric current in the cigarette lighter socket is interrupted or its parameters change. In this case, the protection of the DVR against voltage drops may work. Under such conditions, the registrar will not turn on. To return to normal logger mode, you need to restart the logger using the Reset button. This procedure is described in the operating instructions of your recorder.
To avoid recurrence of such situations in the future, we recommend that you exclude cases of power failure of the recorder.
In this case, you need to connect the power cord directly to the holder of the DVR, which is mounted on the glass, because it is through it that the electric current to the GPS antenna.
Car DVR is a device designed to video and audio recording of the situation around the car while driving or parking. The main purpose is to gather evidence in contradictory circumstances and in case of traffic accidents.
The G-sensor is a three-axis shock sensor that protects recorded information in the event of an emergency.
Models of video recorders with LDWS system are able to track the trajectory of the car and give an audible signal with a characteristic smooth deviation from the lane under the control of a sleepy driver.
You can view recordings from all Gazer DVRs on any media player installed on your computer. It is recommended to install special Gazer Player software for videos shot on models that have a GPS module.
1. Please check the car’s on-board network to ensure that it works properly in the cigarette lighter socket (at a voltage of at least 12 V). The fact is that the cause of such failures is a weak electric current (less than 1.6 A at a voltage of 12 V or less than 1.2 A at a voltage of 24 V).
2. Please inspect the recorder connectors. They must be fastened firmly enough so that these connectors do not dangle during vehicle movement, vibration and shock.
The best solution to the problem of backlash connectors is to use a special accessory for the power cables of the recorder. Our service center will tell you how to buy and install them.
“SD” or “micro SD” format for some models. Information on the format of the memory card and the protocol of work with the maximum supported capacity for each specific model of DVR can be found in the catalog of our products.
You can also use a micro SD memory card with an SD adapter for use in recorders that work with memory cards of the appropriate format. We recommend that you use high-speed memory cards. This will reduce the indentation time between adjacent videos.
We recommend that you use high-speed memory cards. This will reduce the time spent between adjacent videos.
For proper operation of the DVR, a voltage of 5V must be applied to the round input on the housing. We recommend using a complete memory to ensure reliable operation of the device.
The radio comes with all the necessary cables and an adapter to connect it to a compatible car.
CarPlay connects only with a wire.
Initially, this feature is disabled. You can turn it on by going to Settings – special settings – driver settings – video viewing “allow video viewing in motion”. Please note that watching videos while driving is dangerous, this function is intended exclusively for watching videos by passengers.
In the radio program, you need to turn off AF, TA, PTY.
No, the icons on the main screen cannot be changed.
Wi-Fi is turned on by pressing the button to switch the display of cameras.
Yes, there is such a function.
Zinc and aluminum alloy.
The memory card is not inserted, the recording does not start, the automatic shutdown is triggered.
Jumpers / jumpers J1 and J2, mounted on the relay unit board, are responsible for the timer modes of the camera. Jumper J1, located closer to the center of the board, is responsible for turning on the camera for 10 seconds when the ACC signal (ie for turning on the ignition). Jumper J2, located closer to the edge of the relay unit board, is responsible for activating the timer delay of the camcorder after turning off the rear gear (image from the rear view camera will be available on the monitor for 10 seconds after turning off the rear gear).
So. Such cables are compatible. However, if you use the CC155 or CC125 camera with a cable from the CC100, the timer mode function will be turned off.
Rear view cameras transmit images to the monitor using an analog signal. Characteristics of this signal are 540 TVL (720×576) for the PAL standard and 500 TVL (720×480) for NTSC. Resolution is indicated in TV lines (TVL) with the number of elements in the TV image line.
Please make sure that the camera and the tape recorder work in the same video signal standard (PAL or NTSC). You can switch the camera mode from PAL to NTSC using the green wire on the camera connector. After eating the green wire, the camera will start working in the NTSC system.
The effect of the mirror image is due to the fact that, in this case, installed cameras with NTSC color system. Please go to the system calibration settings and enable “mirroring” of each camera.
The 64GB capacity holds about 650 videos, which is about 1 month of using the roundabout system.
The 64 GB media contains about 650 videos, which is equal to approximately 1 month of using the circular review system.
The wire must be connected as follows:
Yellow – power from the +12V battery
Red – signal ACC +12V
Black – ground GND –
Green – signal input for turning on the reverse gear (reverse)
Blue – radio control signal output (to activate the monitor) + 12V
Orange – input of the control signal for turning on the right turn signal
Pink – control signal input for turning on the left turn signal.
The 360 surround view system can work with both PAL and NTSC cameras. For correct operation and display of cameras, you need to connect all 4 cameras of the same color standard (PAL or NTSC). After that you need to reboot the device as well.
The 360 circular view records videos on a memory card, separately, 4 channels (separate recording is conducted from each camera).
Depending on the speed of movement, the working distance will vary slightly, but will be within 10+m. The system can work both at speeds above 30 km/h and continuously. You can specify this during system installation.
The front parktronic system will work either when turned on from the button, or when the speed is reduced below 15 km/h because can be connected to the CAN bus. Also, the front system is equipped with a different activation logic, which allows the device to behave calmly in traffic jams.
The rear parktronic system begins to detect obstacles with a distance of 1.6 m and closer. If the system emits a sound alert, then there is an object in its visibility.
This system comes with two microwave sensors mounted under the rear bumper.
Also included with the system are 4 indicators of system operation, the main 2 of which are wirelessly connected and installed in the front, as well as 2 additional ones for installation on the center pillars to warn rear passengers.
You can output sound using a wired connection through the audio output on the monitor body, using the FN transmitter built into the monitor, or connecting via Bluetooth (only for HR250).
In the settings of the device via Wi-Fi, for example, distribute the Internet from a smartphone or radio.
In the device settings.
In the list of programs, find the HDMI or AV icons and open them.
The TG-FTS sensor, when correctly connected, simulates pressing the button to open the rear door. If the regular system in the car opens when you press the physical opening button, you can install a sensor.
Such operation of the sensor can be caused by incorrect installation.
The sensor must be installed with a white gasket to the ground.